today's DCG

Present your work.
Joe Farina
Posts: 914
Joined: Wed Jan 07, 2015 2:10 pm

Re: today's DCG

Post by Joe Farina »

This is a test DCG hologram done yesterday. The object on the left is a piece of marble painted with squares of different colors. The DCG film is the usual kind, but the pH was raised to 6.35. Two wavelengths were used, 488 and 532. The colors were combinations of blue, green, yellow, and white. Although desaturated in this hologram, the colors came through to a reasonable extent. Power levels for the exposure were 120mJ for blue, and 600mJ for green. Lab temp and humidity were 61F and 53%. There was some damage to the gelatin due to the 1/16 inch polycarbonate sheet which I was using as a cover plate during processing to reduce blotches (which definitely works.) The sharp edges of the plastic dug into the gelatin, due to my carelessness.

In recent holograms, I've switched to using a concave mirror for beam expansion rather than a spatial filter. So far, I haven't been able to detect any difference in the final hologram. As long as the mirror is new, and kept clean, it works very well. Of course, if the spread beam is examined on a white screen, there are irregularities, but they aren't severe. For display holograms of objects, it seems that those irregularities aren't noticeable at all. Using this mirror has made my life much, much easier :) I'm using a mirror with a 4.5mm focal length from Edmund, which is comparable to a 60X objective. They have many other types available at a reasonable cost:

https://www.edmundoptics.com/f/concave- ... ors/12242/

PA250002.JPG
PA250002.JPG (417.04 KiB) Viewed 2761 times
Joe Farina
Posts: 914
Joined: Wed Jan 07, 2015 2:10 pm

Re: today's DCG

Post by Joe Farina »

This is a test DCG done today. Although dim and "washed out" for some reason, it does give an idea of some colors which can be obtained by using a 488/532nm exposure. It is also too green, I think. 96mJ was used for 488, and 350mJ for green, maybe the green should be reduced to 300mJ. Before, I was making the mistake of not keeping the hologram in the alcohols long enough. The emulsion might be about 25u thick, and only 3 minutes was used in the alcohols. After changing this to over 5 minutes, the colors became better.

No fixer was used, just a 100C 1-hour bake after exposure. Later on, I want to test some homemade "fixer" consisting of 2% sodium metabisulfite plus ~5% formalin, adjusted to a pH of 5. I want to use this pH because it's near the isoelectric point of the gelatin, and I don't want to swell the gelatin at the same time the dichromate is being reduced and the gelatin hardened. Maybe this will make no difference, but I want to test it.

Film formula was ~10% potassium dichromate (to dry weight of gelatin). Age of coated plate 2 weeks. Lab temp 63F and 55% RH.

P1010086.JPG
P1010086.JPG (1.33 MiB) Viewed 2268 times
Joe Farina
Posts: 914
Joined: Wed Jan 07, 2015 2:10 pm

Re: today's DCG

Post by Joe Farina »

These are two pics of a hologram done today. I tried a homemade "fixer" (1% sodium metabisulfite, 4% formalin). I dipped the hologram into 3 different levels of the fixer for different amounts of time. There are 4 sections: top (no fixer), next 1 minute, next 2 minutes, bottom 3 minutes. Strangely, the 1-minute fix provided the cleanest result (least fog or haze). I've noticed this before, prolonged exposure to formalin can result in more fog, rather than less (I would have expected the opposite).

Another thing I've noticed is what I call "angular variation of color" depending on the angle of the reconstructing light. For an unknown reason, immediately after finishing the processing (after using the hair dryer after the 100%) the angular variation is hardly noticeable. But after putting the hologram into the oven for the 130F bake (for several hours), the angular variation of color becomes large. This can be noticed in the top row of colors, when moving the light from right to left, the reconstructed wavelengths get longer (blue becomes green).

The oven baking at 130F is apparently doing something to the fringe planes in the emulsion. I recently bought a vacuum oven which I understand changes the physics of drying completely. I haven't tested this yet. In a conventional oven, the surface of the object which is being dried "crusts over" with the exterior drying faster than the interior, potentially locking in moisture. The vacuum oven drastically lowers the boiling temperature of liquids, so that the interior dries at a similar rate as the exterior. That's what I've read at least.

This was a two-wavelength exposure at 488 and 532. Still working on exposure balance, this was 1:5 blue to green power. The photos of the figure look too green (the lace dress should be white). Contrary to expectations, when the result is too green, I think that means that more green power is needed. It seems that more blue is what makes things greener. This may have something to do with the position of 532 in the spectrum. It's hard to judge colors by eye (looking at the laser illuminated objects) because the eye is much more sensitive to green, and DCG is much more sensitive to blue.
P1010084.JPG
P1010084.JPG (1.01 MiB) Viewed 1335 times
P1010085.JPG
P1010085.JPG (1.08 MiB) Viewed 1335 times
Post Reply